My last set of tyres were run at 32psi front and 26psi rear, the pressures were displayed on the dash usually showing within 1psi of what I had set them to.

Sounds legit

The last exhaust I purchased was a slip-on Akrapovic end can for the Gen 4, iirc that was £700. I would have purchased the full system but I was using the bike for commuting to work leaving early in the morning so decided against it. I can’t remember the price of that but maybe in the region of £1600.

Beancounter wrote: Sun Jul 05, 2026 10:53 pm
It's turning into a belter.

Don’t think the ref wanted to go home wtf was he doing at the end, blow the whistle ffs.

What model of bike do you have? And what engine?

Felix wrote: Thu Jul 02, 2026 12:43 am

Saga Lout wrote: Wed Jul 01, 2026 10:17 pm It's the Scots I feel sorry for. They have to discard their DR Congo shirts and pretend they've been supporting Mexico the whole time.

Thank fuck its Mexico next. Running out of paint here.



FB_IMG_1782949257963.jpg

That’s brilliant

The 9r’s have carb heating, they improved it in the later models, double rail instead of the single rail that was on the c’s. I got it bad on my c model back in the day as I used that daily for work, was a pain in the old cock.

gremlin wrote: Wed Jun 24, 2026 8:40 am Bit more detail would be useful. HR stuff?

HR stuff yes, all sorted now, well depends what you class as being sorted. All I’ll say is I’ll be keeping my wits about me and to trust nobody, some proper fuck nuggets about that’s for sure.

Is there anyone on here who is clued up on the above?

Send me a PM if you are.

Cheers

Can you set a boundary? Or does it just keep going until it can't go past a fence or something?


This one has sensors, so it stops if it comes up against something. The really cheap ones you have to put a boundary wire around the edges. The really expensive ones you can create maps using the ...

Just seen a video of Bez apologising to the marshal, giving him his gloves I believe and a big hug. All good!

They released the footage from the onboard camera. When the Marshal attempts to lift the bike something happens and causes the bike to go full throttle, whether it was from him accidentally pulling on the throttle or possibly a fault within the bike and the reason I say that is immediately the ...

Cousin Jack wrote: Thu Jun 18, 2026 9:48 am Not a nice bloke at all, but he was driving a Porsche and I had a Ford Sierra.

Yeah but was it a Cosworth

Yes you can use it as a phone, to a certain extent anyway, WhatsApp, FaceTime etc etc. Possibly even more so if used in conjunction with a iphone but don’t quote me on that.

When I purchased my iPad Pro back in 2018/19 it was a cellular iPad to begin with, had its own number, 5G or possibly 4G then ...

No nothing. I have an appointment at the eye clinic in a few weeks.

Is your eye fully back to normal again? That sounded quite tricky…


Not back to normal.

The pupil is still dilated, I think it’s went down slightly but whether it will go down any more or not I do not know. If I read something with my bad eye closed it’s as clear as anything and when I close my ...

Great to see you up and at it again Wull. 8-)


Some of them are from earlier in the year but I was doing the blades and the cutting deck on the Ventrac last weekend and Monday. I’d have been doing more this week, in fact I would have been back at work yesterday but the wee lass is poorly so I’ll ...

I say it every time but doing the units brings is the best money for me, it requires a lot of hours to do plus because they tend to neglect them I always have to do over and above work on them. Replace broken bits, failed bearings etc. It is time consuming but it is worth it in the end up.

I did ...

Some of the machines at Muckhart that I serviced a short while back. The two GP400’s are what they use for the greens, aprons and tees. There is a third one as well which is more of a back up machine, it only has 2 wheel drive so they don’t tend to use that, especially when the conditions are iffy ...

A vid of the work being carried out on the RTV900 above that had the head gasket failure. That’s back up and running good now. I also replaced the rear axle seal on the BX2350 that I had mentioned before. That required draining all the hydraulic oil, I replaced with fresh oil and a new hydraulic ...